中 EN 中 EN 0 品牌故事 新聞中心 產品中心 解決方案 服務資源 聯絡我們 產品中心 Standard TFT Sunlight Readable Wide Temp. TFT Wide View TFT Bar Type TFT Open Frame MONO(Grap) MONO(Char) Touch Panel Glass Heater LCD Others
128x64 繪圖型 FSTN LCD 模組(含背光), 單色繪圖型LCD模組, 黑白顯示COG繪圖型模組, ST7565P-G, Model No.VGG120608-B(BL) 分享 分享此產品至: ► 128*64 Dots Graphic LCD Module ► FSTN / Transflective / Positive ► Bulit-in Controller (ST7565P-G) ► +3.3V Power Supply ► Backlight:LED (White) ► 8-Bits Parallel(6800/8080) / SPI-3 / SPI-4 檔案下載 加入詢價 規格說明 產品說明 Pin功能定義 產品應用 Resolution (dots): 128*64 Outline Dimensions (mm): 39.2*78.6*3.5 View Area (mm): 34.0*22.0 Dot Size (mm): 0.225*0.255 IC: ST7565P-G Backlight: LED (White) I/F: 8-Bits Parallel(8080/6800) / SPI-3 / SPI-4 Absolute Maximum Ratings Item Symbol Min. Max. Unit Operating Temperature TOP -20 +70 °C Storage Temperature TST -30 +80 °C Electrical Characteristics (Ta=25±2°C) Item Symbol Condition Min. Typ. Max. Unit Power Supply Voltage VDD - - 3.3 - V Power Supply Current IDD VDD=3.3V - 0.25 0.35 mA Backlight Unit (Ta=25±2°C) Item Symbol Min. Typ. Max. Unit LED Forward Voltage V - 3.5 - V LED Forward Current I - 20 - mA Color White Pin No. Symbol Description 1 /CS1 This is the chip select signal. When /CS1 = “L” and CS2 = “H”, then the chip select becomes active, and data/command I/O is enabled. 2 /RES RESET signal 3 A0 This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command. A0 = “H”: Indicates that D0 to D7 are display data. A0 = “L”: Indicates that D0 to D7 are control data. 4 /WR (R/W) When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active. The signals on the data bus are latched at the rising edge of the /WR signal. 5 /RD (E) When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active. The data bus is in an output status when this signal is “L”. 6~13 DB0~DB7 This is an 8-bit bi-direction data bus. When serial interface is selected (P/S=”L”) DB7 : serial data input (SI); DB6 : the serial clock input (SCL). DB0 ~ DB5 should be connected to VDD or floating. When the chip select is not active, DB0 to DB7 are set to high impedance. 14 VDD Power supply for logic. 15 VSS Ground (GND) 16 VOUT Connect a capacitor between this terminal and VSS 17 CAP3- Connect a capacitor between this terminal and the CAP1+ Terminal. 18 CAP1+ Connect a capacitor between this terminal and the CAP1- Terminal. 19 CAP1- Connect a capacitor between this terminal and the CAP1+ Terminal. 20 CAP2- Connect a capacitor between this terminal and the CAP2+ Terminal. 21 CAP2+ Connect a capacitor between this terminal and the CAP2- Terminal. 22~26 V4~V0 This is a multi-level power supply for LCD module. V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧VSS 27 C86 This is the MPU interface switch terminal C86=”H”:6800 Series MPU interface C86=”L”:8080 MPU interface 28 P/S This pin configures the interface to be parallel mode or serial mode. P/S = “H”: Parallel data input/output. P/S = “L”: Serial data input. 29 LED_A Back Light LED Anode 30 LED_K Back Light LED Cathode #FSTN LCD模組 (FSTN LCD Module) #黑白顯示 (Monochrome Display Type) #繪圖型 (Graphic Display Type) 返回上頁